Spring Winder - Build your own springs

Home Model Engine Machinist Forum

Help Support Home Model Engine Machinist Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
The design and drawings were published in Model Engine Builder in issue # 19.
If someone wants detailed drawings of this winder, the cost of a digital issue is just $6 e-mailed to anywhere in the world. www.modelenginebuilder.com if you want to take a look at the back issues.

Subscription to Model Engine Builder Magazine - 4 Issues

You'll find the back issues at the above link even tho it says subscription.
 
The design and drawings were published in Model Engine Builder in issue # 19.
If someone wants detailed drawings of this winder, the cost of a digital issue is just $6 e-mailed to anywhere in the world. www.modelenginebuilder.com if you want to take a look at the back issues.

Subscription to Model Engine Builder Magazine - 4 Issues

You'll find the back issues at the above link even tho it says subscription.
Thank you for the link. I have purchased Issue 19 and now have the drawings. There does not seem to be a dimension for the overall length of the body. What overall length did you make yours? I’m looking forward to possibly redesigning it for ease of manufacture and making it.
 
Sorry, just noticed this. Mine is 3.5".
Thank you I have purchased issue 19 and have produced a 3D model and a set of detail drawings. Instead of having to produce a square hole I am going to machine a slot and fit a retaining plate to secure the adjusting bar in place. All my designs are in metric.
 
Finally completed my version of the spring winder. i have replaced the square hole in the body with two guide pins.
 

Attachments

  • 68048F9A-1443-45A2-AF69-37D7A620001B.jpeg
    68048F9A-1443-45A2-AF69-37D7A620001B.jpeg
    118.5 KB
  • 7B06E903-0FBB-40D9-BF1D-4875A26C4EBC.jpeg
    7B06E903-0FBB-40D9-BF1D-4875A26C4EBC.jpeg
    129.4 KB
  • 2FE41A0A-D9ED-471F-A978-C8080A45C838.jpeg
    2FE41A0A-D9ED-471F-A978-C8080A45C838.jpeg
    122.8 KB
  • 520099A6-C459-4F16-9107-9729AF0C64E4.jpeg
    520099A6-C459-4F16-9107-9729AF0C64E4.jpeg
    121.5 KB
Last edited:
Jerry, that’s a good idea. The winder works well and because the mandrel is not limited to length longer springs can be made and then cut to length as you suggest.
 


I saw that video some time ago.

However is the hand cranked item easier to use?


Having seen Andrew Whales video I made one of these and found it difficlt to use because you are trying to locate the round part of the tool onto a round mandrel. I managed to overcome this by replacing the round wedge item with a flat plate with a bee machined into it. The problem with this arrangement is you require different thicknesses of plate for different spring pitches. However I also found difficulty in holding the tool with one hand and using the other to control the lathe.

What I like about Jerry’s version is that you have complete control when making a spring and it provides a clamping facility for the spring and the spring pitch is infinitely variable. The one that I made removes the requirement for a square hole, but if you have a broaching capabi it would be less of a problem. I am developing a second version which removes the requirement to drill the deep hole through the body.

hope this helps
 

Attachments

  • A3AF2486-0A67-482F-92AE-F27C386C0759.jpeg
    A3AF2486-0A67-482F-92AE-F27C386C0759.jpeg
    366.4 KB
  • 686700AE-F1BB-4F6C-B3C0-0371A7E867C4.jpeg
    686700AE-F1BB-4F6C-B3C0-0371A7E867C4.jpeg
    172.9 KB
  • 1A7D974B-2FDC-44E5-9C80-FB5B920BF8AF.jpeg
    1A7D974B-2FDC-44E5-9C80-FB5B920BF8AF.jpeg
    123 KB

Latest posts

Back
Top