Search results

Welcome to the group. I think what you're looking for is on the HMEM home page:

The Monitor was in a couple of other shots I took. I'm sorry they don't show more detail. John

Here are a few photos I took at the 2023 show. Many thanks to Mike and everyone that organized and set up the show. Looking forward to the 2024 show; the dates are September 28th & 29th. John

I made a new head gasket from 0.4 mm graphite foil sheet. The engine is back together, and with a little fiddling is running pretty well now. I took it to a show this weekend and ran it for at least 2 hours over a three day period. The new gasket seems to be holding up so far. Here's a...

Got the engine apart, and verified the head gasket is indeed blown.

Very nice! I'm currently building the water cooled version. John

Mike, thanks for the information and the kind offer to send a sample. I will keep it in mind as I consider all the options. Ideally, I'd like something a little thicker, e.g. 0.015 inches (0.4 mm) or so. The gasket is relatively small - approximately 2 inches (50 mm) in diameter. I do not...

Mike, could you kindly provide a little more information. What sort of fiber/fibre are you speaking of? A link to a specific product would be helpful. The gasket currently in the engine (the one that blew out) I made from a standard paper gasket material, commonly available at auto parts...

I put this aside a few months ago, and it's time to try to fix it. After reading some older posts about gasket material, I think I'm going to try Teflon sheet. I have a question for those who have used this successfully. Should I use any type of sealant with the Teflon, or should I just leave...

Looking at this a little closer, it appears there are/were at least two different sizes of Olds casting kits. My engine has 1-7/8" bore, 2" stroke, and 8" diameter flywheels. There is a letter "B" cast into the side of the hopper, and the drawings say "Breisch". The MiniSteam engine has a 7/8"...

You might want to contact Ministeam. I believe they sold the casting kits at one time. Their web site says the kits are out of stock, but they may be able to supply the plans. John

Looks good! I like using Hall sensors for model ignition. They are small and less obtrusive than automobile points. I have one on the Fairbanks-Morse in my avatar and one on my Stickney. John

Skeehorse, I posted some pictures of the Olds in the "Photos and Videos" section. John

I'm posting these at the request of another member. I acquired this last fall from another modeler. It is not currently running and needs a little work before it will be ready to try. There are a few projects in the queue ahead of this one, so it will be awhile before I begin working on it. John

I will get some pictures of the Olds for you. At the moment it's stored in the basement. I'll have to bring it upstairs where there is better light for pictures. I will try to do it this weekend. John

Which Breisch model do you have? I have an Olds that is mostly finished but not running, and a set of castings for an air cooled Associated. John

Are those the correct dates? That's a Friday and a Saturday. In past years the show has been on Saturday and Sunday. The past few years the two shows have been on the same weekend, but that hasn't always been the case. In 2015 they were a week apart and we were able to attend both shows. It...

I just realized I should have put something in the pictures for scale. The engine is about 25 inches tall, including the wood base and the brass fuel tank on top. John

Here are a couple of photos of the little Stickney, reassembled with the repaired crankshaft. The engine is more or less complete, with the exception of the ignitor which is non-functional at this point. I've rigged the engine for spark plug ignition, with an electronic buzz coil and hall...

Fingers crossed, hoping it works out well.